|
|||||||
String gauge question Related threads: Tech: Bill Keith's mechanical banjo pegs (14) Banjo Head Torque Wrench (26) help: banjo pickups (9) Banjo repairs (21) Nylon Banjo Strings (17) Banjo: Does string size make a difference? (10) Fielding Banjo Mute (43) HELP - Banjo Doesn't Work Properly (38) longneck banjo (what strings) (8) Setting up a cheap banjo (27) Nylon Banjo Strings (19) Clawhammer Strings (2) Banjo Talk - Long Neck and Head Tension (15) Banjo Setup and Sound Problems (14) Help: recording 5-string banjo (2) Got an old pick up? (17) Banjo string advice (22) Bit the bullet & put pick up in banjo (8) |
Share Thread
|
Subject: String gauge question From: Jack Campin Date: 23 Oct 19 - 05:04 AM Somebody out there must have a string gauge calculator. I've never used one. I have two cümbüşes - 12-string fretless banjos. One is the standard Turkish size and stays in the standard Turkish tuning. The other is a bit smaller (probably made for schools around 1950, recently refurbed by a first-rate banjo maker who put a natural skin on it) and I want to put it a tone down to play at Arabic pitch level. But it feels like I need heavier strings to get adequate pitch stability and stronger tone. What should I use? Can somebody calculate the gauges for me? Scale length 46cm. Pitches I want: lowest pair G below middle C (same as violin G). Above that, paired and going up in fourths: AA DD GG cc ff. Currently I have it in an alternate tuning with CC instead of AA - not as playable but a lot more stable. They need to be loop end, not sure who can do that. |
Subject: RE: String gauge question From: Stanron Date: 23 Oct 19 - 05:21 AM There are a few of these on line now. Here is the one I have used for some time. Scroll down a bit to use it. http://www.mcdonaldstrings.com/stringxxiii.html As for loop mends, you can usually remove the 'ball' or 'toggle' to leave a usable loop. |
Subject: RE: String gauge question From: Stanron Date: 23 Oct 19 - 05:22 AM Too much 'm'. |
Subject: RE: String gauge question From: Jack Campin Date: 23 Oct 19 - 09:29 AM Thanks. What I get from that: G - .050 wound A - .040 wound D - .030 wound G - .020 wound C - .014 plain F - .010 plain Which all seems plausible. |
Subject: RE: String gauge question From: GUEST,Jerry Date: 24 Oct 19 - 06:16 AM I reckon that your scale length might be a problem though, so I guess that you might need to be a shade lighter, especially on the higher strings. I would check out extra light mandolin string gauges, with some extra customs for the As and Cs. And surely the G ought to be about .042, if it’s only a tone lower than the neighbouring A? |
Subject: RE: String gauge question From: Nick Date: 25 Oct 19 - 04:20 AM Try http://stringtensionpro.com/SelectInstruments which includes cub us as an option if you haven’t already found it or the answer. |
Subject: RE: String gauge question From: Big Al Whittle Date: 25 Oct 19 - 04:47 AM when I had a long neck banjo - I used to use rotosound loop strings. They had a wide choice. |
Subject: RE: String gauge question From: Jack Campin Date: 25 Oct 19 - 05:10 AM This cümbüş is nonstandard in two ways - it's a small size that never caught on, and I'm using it at a lower than usual pitch. Nice for a calculator site to include them, but I can't expect a packaged solution. Anyway, I've got a d'Addario set meeting the above spec and I'll put them on shortly. |
Subject: RE: String gauge question From: Nick Date: 25 Oct 19 - 07:03 AM It did have a custom setting where you could choose your neck length (standard is 540mm it suggested) There is a formula at Tensions if your maths is good - which I'm guessing it might be. As some asides... I made a string gauge calculator that worked as I wanted it to as a friend was a big "open C put piano strings on" and wondered why he took it back to the menders. Most instruments don't say what the overall force should be. A friend has a very expensive, very old Martin guitar which no longer gets played outside of the house (which he once lent me for a few days when I was visiting - no greater love etc etc) which has a VERY specific instruction NOT to put strings over a certain weight on. But as far as I can see stringed instrument manufacturers recommend a weight of string but not really giving the range where damage may occur. I did check a few sites and don't think they state it really. The first guitar I had was a £10 Tatra classical and I think they said 'do not put steel strings on this or...' but that is about it I have a friend I play with who is happy with adjusting truss rods etc who has given me a little more confidence to experiment. But also to see the difference that different sets of strings make to the action and playability of the guitar Mind you, I don't think whistle manufacturers tell you what is the hardest you can blow. |
Subject: RE: String gauge question From: Nick Date: 25 Oct 19 - 07:07 AM And here was another very good resource too for non standard things. But still doesn't address the 'What is the most force I can safely put on this instrument?' because of course they are all different and how does one know? |
Share Thread: |
Subject: | Help |
From: | |
Preview Automatic Linebreaks Make a link ("blue clicky") |